Seats Subassembly Process

ENGINEERING GRADUATE

FUNCTIONS

STRATEGIC: 55 %.
- **Develop strategic investment studies based on GVD program timings for code 1 and others assigned projects focused on reducing** waste and losses based on Plant CD and business case analysis.
- Create Critical Route Timings with attainment to the GVD for code 1 and others assigned projects in detailed for all GA Line.
- Create Specification Package considering Process and Product Standards, GD&T, government regulations, cycle time of the process, establishing all the KPI´s and deliverables based on Stellantis standards.
- Plan and coordinate interaction with the productive area for the introduction of new machinery and equipment in new or existing facilities for the manufacture of vehicles designated to Mexico Plants.
- Development and approval of layouts, program issuance and control plans.
- Supplier technical evaluation for purchase sourcing procedure to select the supplier desire based on the technical proposals for Tooling and Machinery Manufacturing.
- Creation, issuance and follow-up of Indirect Source Package and Purchase Requisitions to procure new machinery, tooling or facilities as product and process requires.
- Consider and assure the compliance of the Government Policies and regulations as part of the tooling/Facilities.
- Project management since the program approval phase until successful launch identifying the resources needed in each step for success vehicle vertical Launch.
- Feasibility studies Development to identify and fix the issue since the product design phase avoiding impact to the production line based on DFA, Value Engineering, PFMEA´s and Digital Scroll Review.
- Maintain actual ISO certifications. Contributing and managing projects based on Quality and environmental policies.
- EPM Early product management - design for assembly / make match with process design (tooling & machinery concept design )
- Tooling design engineering, revision and approval in agreement with the plant team, CoC, product engineering and suppliers.
- Implement Kaizen methodology from a proactive approach on early project phases.

OPERATIONAL: 30%
- Tooling buy off, installation, validation and start up on site floor on production plants. Coordinate the tooling/equipment installation tryouts, certification tests and assurance of the right operation of the equipment.
- Support plant team in the analysis and solution for quality, feasibility ergonomics and safety issues
- Train plant staff in the use of new technologies at Supplier of Plant facilities.
- Supply the appropriate tooling, devices and equipment to perform the assembly or test of all the components for the new models or versions at General assembly.
- Load and upload tool/machinery/facility 3D models and graphics from/into Team Center database.
- Get knowledge of TCF areas for succession plans: Seats subassembly make process, oven & iron processes to handle leather wrinkles, sequinece of seats subassembly process, H point measurement, scroll for subassembly seats, trim dressing line, Final Line and EOL processes. Like : Glass Cell, Badges installation, IP Setting, transmission flashing, pull out test, End Off Lines test, torque tools, Multi spindle torque tools, torque reaction arms, powertrain indexing process,
- Coordination of receive shipping tool/machinery from cross board countries supplier until plant arrival.

RESOURCE MANAGEMENT: 15%
- Assign proper people to perform buy off, validation and process verification of tooling, equipment and process.
- Control, spend and tracking Funds assignment for code1 and others assigned new projects at ME MP Portal.
- Create and lead a cross functional team for tooling development and validation at suppliers and plant sites.
- Track and spend the funds assignment from kaizen´s based on the Plant Cost Deployment with B/C approved by Controller.
- Schedule supplier support for training and pilot phases at plant, based on plant training requirements
- Lead and Tracking Suppliers activities during project phases (Estimation, Design, Tryouts, Installation, Pilots and Launch).

POSITION REQUIREMENTS

Experience for all GA Seats Sub assembly position:

- 5 Years of experience as manufacturing engineer in the automotive industry handling all projects phases for Machinery & Equipment: Design concept, Design reviews, Manufacturing Phase, Buy Off, Dimensional certification, Shipping, Installation and Validation and run Pilots and get Launching Phase Supervision.
- 5 Years of mínimal experience on 3D/2D CAD management.
- 5 Years of mínimal experience on Investment studies related to long and medium projects.
- 5 years of minimum experience in Trim assembly process as : seats subassembly process, EOL and iron -oven seats processes, Urethane Glass cell, IP Setting Install, Badges Install, Door Off / Door On, and Sun Roof Install or similar preferably in the automotive industry.
- 5 Years of demonstrable experience in Subassembly seat processes, Assist arms, S